Leading 10 usual forklift crashes ， forklift procedure need to take notice of these issues ！.
Leading 10 usual forklift crashes ， forklift procedure need to take notice of these issues ！.
Blog Article
Don't ignore the forklift at the workplace. If the operation is not good, there will be serious accidents in minutes, and there are numerous mishaps entailing forklifts.
Instance 1: The forklift freight obstructed the vehicle driver's view, and the individual in front might not be discovered, leading to a rolling accident.
Case 2: In order to maintain the balance of the forklift when raising hefty items, the staff members utilized their body weight as the counterweight, which practically triggered casualties.
Case 3: The width of the forklift freight goes beyond the permitted width of the route and hangs on the roadside rack, which nearly triggers an mishap.
Case 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift driver did not see the pedestrian, and the pedestrian did not see the forklift.
Situation 6: The forklift lifts the personnel unlawfully, the forklift motorist does not wear the safety belt, the forklift lifter drops and the driver is squashed when the forklift surrender.
Case 7: The forklift driver did not put on a seat belt and dropped from the automobile when it rolled over and was squashed.
Forklift procedure ought to pay attention to these issues ：.
Begin.
1. Before beginning, observe the surroundings, and after confirming that there are no barriers that impede the safety of driving, beep the horn first and afterwards start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale need to be safe prior to starting.
3. When the forklift starts with a load, the motorist should initially confirm that the tons is stable and trustworthy.
4. The start needs to be slow and consistent.
Driving.
1. When driving, the height between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole should be tilted backwards. .
2. Do not raise the fork too high when driving. When going into and leaving the work site or while driving, take care that there will certainly be no obstacles overhead. When the lots is traveling, the fork needs to not be elevated too high, which will influence the security of the forklift. .
3. After unloading, the fork must be decreased to the normal driving position prior to driving. .
4. When transforming, if there are pedestrians or lorries nearby, the driving signal ought to be released initially. High-speed doglegs are restricted. High-speed sharp turns will certainly create the lorry to lose lateral stability and tip over. .
5. When the forklift is downhill, it is strictly restricted to switch off the fire and slide, and it is forbidden to brake all of a sudden while driving with tons unless there are unique conditions.
6. When the forklift is running, it has to obey the traffic rules in the factory and should keep a specific security distance from the automobile ahead. .
7. When the forklift is running, the tons should be in the lowest position that does not hinder the driving, and the gantry ought to be correctly tilted back. The load shall not be raised other than when piling or filling. .
8. The elevation of the tons need to not block the chauffeur's sight. In special circumstances, when the thing influences the forward vision, drive at a reduced speed when reversing.
9. It is forbidden to turn on the ramp, neither to drive throughout the ramp. .
10. The risk-free driving speed of the forklift in the factory location is 5 km/h, and it needs to drive safely at a low rate when getting in the manufacturing workshop area. .
11. When the forklift is lifted, raised or driven, it is prohibited for workers to stand on the fork to hold things and play a stabilizing function. .
12. If problems are located, they will certainly be repaired and reported in a prompt fashion, and they will never ever run with diseases or conceal them.
filling and discharging.
1. When fork-loading items, the range between both forks ought to be adjusted as required to make the tons of both forks balanced and not skewed, and one side of the thing ought to protest the rack. .
2. It is forbidden to collaborate with a single fork or make use of a fork top or pull. In unique scenarios, safety indication must be established to remind bordering pedestrians. .
3. In the process of loading and discharging items, the forklift needs to be braked with the brake. .
4. The rate of the vehicle must be slow and constant. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled objects and harm individuals. .
5. When using a fork to fork the goods, the fork needs to be as deep as possible under the tons, and it should be noted that the fork pointer ought to not touch various other goods or items. The lots should be supported with marginal back tilt of the gantry to make sure that the load does not slide backwards. The pole can be slanted forward somewhat when the lots is lowered to enable simple positioning of the lots and extraction of the forks. .
6. It is prohibited to fork items at broadband and collide with difficult items with the fork head. .
7. When the forklift is functioning, it is forbidden for people to stand around the fork, so as to stay clear of the collapse of the goods and injure people. .
8. Overloading is forbidden, and it is banned to make use of forks to lift personnel to participate in high-altitude operations to prevent high-altitude dropping crashes. .
9. It is not permitted to use the brake inertia to slip, put, round or roll objects. .
10. It is not enabled to utilize forks to choose, transform pallet discharge.
Leaving .
1. It is restricted to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you have to dump the goods or reduced the fork structure.
2. Draw the hand brake handle to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique conditions, such as the vehicle driver does not leave the lorry's view and does not go beyond 1 min).
4. Eliminate the secret. .
Forklift Operation Precautions.
1. Before and after the forklift operation, the appearance needs to be examined, and gas, lubricating oil and cooling water ought to be added.
2. Examine the safety and security efficiency of starting, running and braking.
3. Examine whether the lights and horn signals are total and efficient.
4. During the procedure of the forklift, examine whether the pressure and temperature are normal.
5. After the forklift is running, the exterior leak ought to also be examined and the seals must be replaced in time.
Forklift Safety Operation Specifications.
1. You must examine prior to leaving the automobile;.
2. When you experience someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight ought to be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be also sharp to avoid the tendency of " cost-free turning";.
6. Adding and down the Electric Forklift Truck for Warehouse slope should be slow-moving and uniform, and no activating the slope is permitted.
7. Do not drive across the slope. When the gradient is more than 10%, the car should be driven in reverse when going downhill;.
8. When the forklift workers lug the goods and progress, if they encounter big or hefty products and most likely to the chauffeur's view, they should take the turning around workout
.
The "Eight Prohibitions" ought to be adhered to in the operation.
1. Solitary fork procedure is not allowed.
2. It is not enabled to raise the goods for far away driving.
3. It is not permitted to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not allowed to utilize Stand-on Electric Pallet Stacker inertia pressure to grab the goods.
6. It is not permitted to use braking pressure to expatriation round or easy-to-roll objects.
7. It is not enabled to bring individuals to work with the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Auto parking is not allowed under the list below conditions.
1. Curves, narrow roads, railway crossings;.
2. Areas with a longitudinal incline more than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same size as the barrier must be within 20 meters at each end.
Web：https://www.onenforklifts.com/
Email：info2@onen.cn
Phone：+86 13827083844